![python record data from globalsat bu-353-s4 usb gps receiver python record data from globalsat bu-353-s4 usb gps receiver](http://garbtech.co.uk/wp-content/uploads/2016/01/IMG_20160108_033926-225x300.jpg)
- Python record data from globalsat bu 353 s4 usb gps receiver install#
- Python record data from globalsat bu 353 s4 usb gps receiver serial#
- Python record data from globalsat bu 353 s4 usb gps receiver update#
- Python record data from globalsat bu 353 s4 usb gps receiver password#
- Python record data from globalsat bu 353 s4 usb gps receiver windows#
It should be a case of:-Īnd check that 'camera_method' in /root/scripts/global.rc is set to 'picam'
Python record data from globalsat bu 353 s4 usb gps receiver install#
Sorry, it looks like the Raspbian install guide is sadly lacking information here. The picam script requires Python3 to be installed. GPS annotation will work for the Pi camera if you use the picam script instead of the pivid one. If you want to disable the Pi camera's LED then add the following to the /boot/config.txt file and reboot. Reboot and (all being well) everything should start when your Pi has booted up. You can test it works with this /etc/init.d/rc.local start Precedent over the progam defaults and also matching variables found in /root/scripts/global.rcĪn easy way to have the dashcam script start automatically from boot up is to add it into the The other scripts will try and exit cleanly if ki l led with an INT, TERM or USR1Ī global.rc file can exist at the root of mounted USB storage. pkill -USR2 pwr_butt (or pkill -SIGUSR2 pwr_butt) will reboot the Pi. Using SIGUSR2 will do the same but issue a reboot instead.Į.G. Killing pwr_butt with a SIGUSR1 will stop all running programs and shutdown the Pi. 'usb_directory ' root mount point global.rc (if it exists) respectively. These defaults will be over ridden by values found in /root/scripts/global.rc followed by the If no arguments are passed to the dashcam.sh then the defaults of GPS, motion, pivid & pwr_butt areĮnabled. If arguments are used then any global.rc *_enabled settings are ignored. This will start only the pwr_butt and pivid.sh camera recording programs. Progra ms using the dashcam.sh script with arguments: Pwr_butt - Monitors (GPIO 2 by default) for a button pressĪlthough the scripts can be used separately the ide a is to start them from the dashcam.sh programĪnd stop them with the pwr_butt program (usually via a button press). Pivid.sh - Pi camera recording using the raspivid command Picam.py - Pi camera recording using the picamera package (requires python3) Motion_camera.sh - Runs motion to record video when a USB camera is connected Gps_logger - C program to manage the GPS (via gpsd) Global.rc - Resource file for all the global variables Mounts USB device, rotates logs, disk cleanup etc.įlash - C program to flash LEDs as required (GPIO #, count, delay, finish on/off) Has many values used by these scripts which you can change to best suit your needs.Īudio.sh - Uses arecord to save audio recordings to the audio directoryĭashcam.sh - The main startup script. (as the root cd wget -O scripts.tar tar -xf scripts.tar chown -R 0:0 scripts rm scripts.tarĪ directory called "scripts" in /root should now contain all the required files. SAMBA (if you wish to access the files over a network) Install the GPS apt-get install gpsd libgps-dev
Python record data from globalsat bu 353 s4 usb gps receiver serial#
If you are using a serial GPS remove the ttyAMA0 information from vi /boot/cmdline.txtĭwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwaitĭwc_otg.lpm_enable=0 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwaitĬomment out the ttyAMA0 line in /etc/inittab (at the very end of the vi /etc/inittab Webcontrol_port 9080 (required for the GPS text annotation)Ĭamera /usr/local/etc/nf (only needed if you are going to use the included mkdir /etc/motion/run chown camera /etc/motion/run Stream_localhost off (to allow viewing of the video stream remotely) Stream_port 8080 (required for the GPS text annotation) The bold variables are required, the others settings are recommended or my defaults.įramerate 12 <- change to suit your camera Install and configure motion (primarily for the USB apt-get install vi /etc/motion/nf (an alternative text editor to vi is nano)
Python record data from globalsat bu 353 s4 usb gps receiver update#
Update the apt-get apt-get dist-upgradeĪdd the camera useradd -m -G video passwd su - ~ $ mkdir -p front rear sound usb logs/tmpĬhange the file permissions so the camera directories are available to all (only needed for ~ $ chmod -R 777 ~ $ exit Log back in as 'pi' and change the root ~ $ sudo su passwd Select Expand filesystem (if all of your SD cards space has not been allocated)Ĭhoose and reboot (or from the command line: sudo reboot) Advanced Options -> select Hostnam e (choose the desired name for your Pi) Internationalisation Options -> Change Timezone ( set the timezone to your location)
Python record data from globalsat bu 353 s4 usb gps receiver password#
Change User Password (for the 'pi' account) to one of your choosing The default password for the user 'pi' is: raspberry
![python record data from globalsat bu-353-s4 usb gps receiver python record data from globalsat bu-353-s4 usb gps receiver](https://i.ebayimg.com/images/g/woMAAOSw2s1UvU-V/s-l400.jpg)
Python record data from globalsat bu 353 s4 usb gps receiver windows#
(If you do not have ssh installed then for Windows check here, PuTTY is a popular choice, For instructions on installing an OS image to your SD card please see here or here.Īfter Raspbian has been installed login to the Pi from your computer using ssh.